This machine has two models which is “Stand Model” and “Floor Model”, each model has two specification “Carry Can” ( no can provided ) and “Carry Bottle” (8 bottles provided ), customers can choose any type they need. “Stand Model” is more convenient for geting in and out of the material, “Floor model” is more stable. “Carry Can” can Carry various kinds of can (User should prepare container by himself. The max diameter of container is 180mm, the container height range is from 65mm to 180mm), “Carry Bottle” has a holder can Carry small glass bottles (each side Carrys 4 small glass bottles, total is 8 small glass bottles). Each bottle capacity is about 195 ml.
KS-370 “Floor Model”
KS-370 “Stand Model”
Main Technical Parameters
Installation
1、Installation for “Stand model”
(1) Install suction pad under the base plate of column support.
(2) After column is in place, rubber stoppers are fixed around the base plate of column support (see below) with expansion screws ;
(3) Install the main engine on the column support.
2、Installation for “Floor Model”
Four foot springs are placed inside the spring seat hole of the base plate of main engine, ready-to-use.
Operation
1、Put materials and grinding media (mill bead) into can (or bottle) to be ground and dispersed. Mass ratio of material – bead refer to below table.
2、Put the sealed can on the clamping device of machine, turn handle to tighten it, clamping force can not be over or can will be deformed (or bottle) and damaged clamping device .
3、ase don’t use at one side. If it must be used at the one side, please put can (or bottle) within same volume water at the other side.
4、If using glass bottles on the “Carrying Can” model, in order to improve dispersion efficiency, clamp two small glass bottles symmetry. Also pay attention to the clamping device of two side balance.
5、Set the required grinding time then start.
6、After finishing grinding, please confirm the machine is completely stopped, then turn handle to open clamping device and take out the test cans (or bottles).
7、Work is completed, cut off the power and do cleaning work in time.
Four-Hole Gripper (Only “Carrying Bottle” model provided)
1. Loosen both sides of butterfly screws, separate the four-hole gripper.
2. Put small glass bottles into the gripper. (Test bottles must be the same size as we provide)
3. Cover the gripper and tighten both sides of butterfly screws.
4. Put the whole gripper into the clamping device of Quick Worker.
5.When installed, it must be paid attention to aiming two slots of four-hole gripper at straight pin of clamping device.
Notice
1、Please change lubricant of crankshaft after operating new machine for 100 hours, then just check and replenish lubricant periodically.
2、The maximum total grinding weight including grinding can (or bottle) can not exceed 5 kilograms so as to avoid damage of machine.
3、Please do cleaning & maintenance for guide-bar and screw of the grip apparatus.
4、For increase of service life of Quick Worker, when working time exceeds 90 minutes, please stop the machine for 10-15 minutes, it should be taken a rest for short time then starting again, it can avoid the machine over-heating.
5、Have a great heating produced when working,, please try to put the machine in good ventilation conditions of the workplace.
6、Our company will continuously improve and develop products according to the needs of market and customers. Without prior notice if there is the latest version of the documentation.
Ordering Information:
| Type | Name |
| KS-370A | “Stand Model” Carry Can |
| KS-370B | “Stand Model” Carry Bottle |
| KS-370C | “Floor Model” Carry Can |
| KS-370D | “Floor Model” Carry Bottle |
มาเป็นคนแรกที่วิจารณ์ “Twin Arm Shaker ( Fast Mixer )”
สินค้าที่เกี่ยวข้อง
Film Application
Film Application
Adhesion
Leneta
TQC Sheen
Color/Gloss
Hardness
รีวิว
ยังไม่มีบทวิจารณ์